NOTE: I have added instructions for a table lamp using the picture frame room box at the end of this project.
A popular & very informative, world-wide, online miniature group (CAMP, owned by Den Mother, WMarie Werth THECAMPemail@example.com ) has requested instructions for my concept of using simple wooden picture frames to construct room boxes. I believe it was in early 2000 that I developed the idea and have since used it many times, in different ways and sizes, to house a wide variety of miniature settings. The Frame Boxes have become a standard in the hobby because they are easy and inexpensive (shopping around one can find nice quality wooden frames for just a few dollars each) to construct & require no power tools. Den Mother suggested I put the instructions on this blog to share with as many miniaturists, around the world, as possible, so here you are: (please pardon the quality of the photos herein; they were scanned from the magazines they were published in, not giving the best results. But they should give you a visual idea of the frame method)
-For an approximate 8” wide x 10” high box with a raised base use five identical, 8” x 10” glass fronted, wooden picture frames. Remove everything from the frames & set aside. Assemble the box by gluing the long ends of two of the frames to the long face of two more of the frames. Make sure all inside corners are flush and all is squared-up
These two photos show IF THE SHOE FITS from 2001. It is 8" by 10" and
has a solid back wall and three glass walls..
-For an approximately 10” wide x 8” high box follow the directions above but glue the short ends of the frames together. If desired a 5th frame of the same size may be glued to the bottom of this size box to act as a base.
This is A FAMILY THANKSGIVING DINNER from 2007.
It uses four 8" x 10" frames, with the 10" being the width and the 8" being the depth.
In this piece the back wall is the only solid one, the other three being glass.
You can also see how a selection of holiday postcards were used to decorate the
outside of back wall. This used wooden chess pieces as feet.
-5” x 7” frames may be used for smaller displays, for either smaller scale settings or to showcase one special piece.
-10” x 13” frames may be used for larger/deeper displays or a two sided display box which would then be divided down the interior center.
A PILGRIM'S PAGEANT uses four, 10" x 13" frames. It is a 2 sided piece with the play viewed on one side and back stage on the other. The down-view, photo below shows how the box was divided in half. The small section the the middle hides the wiring.
-Four, 8” x 16” picture frames may be used in a slightly different way than the others. Place a bottom frame face down and then glue another frame to the top edge for the front and backs and then glue the 4th frame to the top of the assembly. This assembly should be glued and pegged or screwed together for strength. The two ends of this box will not be glassed.
An Art Deco New Years Eve Celebration from 2003 uses four 8" x 16" frames; one each on top & bottom and front and back. The end walls between the frames are filled in with mat-board the outside decorated with an outdoor scene and the inside papered to match the inside.
- Suggested but not essential: Once the glue holding the frames together has set you may reinforce the box with counter-sunk nails or pegs inserted in pre-drilled holes. To do this, on the rabbet section of the two inset frames, drill holes (two each, spaced centered, side to side and approx. 2” up from the bottom and 2” down from the top) no bigger than the thickness of bamboo skewers. There will be a total of eight holes. Drill through the one frame and on into the one it is glued to, being careful not to disturb the face of the frame. Glue pieces of bamboo skewers into the holes, snipping on any excess flush with the frame. If necessary, use a sharp knife to make sure the pegs are flush with the frame. Paint or stain the exposed ends of the pegs to match the frame.
-Depending on what will be displayed, housed or the setting, you have the choice of having no solid walls, just a back wall, two or three adjoining walls, or two solid walls opposite each other. The glass walls and glass top will let in plenty of light. Permanent access to the box will be from a removable top.
-The outside of the box may be left as is or painted as desired. It may also be accented with various cut-outs/jewelry findings/stickers, etc. to go along with the theme of your setting.
This little Easter themed store, THE GOOD EGG, from 2004, with a solid back wall and three glass walls shows how the frames can be decorated to go along with the theme of the box.
-Measure and cut a piece of ½” thick foamcore or wood for your floor. If you do not have foamcore or wood you may choose to glue thinner pieces of other materials together for a ½” thickness. Finish the floor as desired, before or after gluing into box.
For the solid walls decide what you want to be seen from the exterior of the box. This can be as simple as plain or patterned paper, or you can decorate them with words or poems, a collage of pictures, or a photo, all to go along with the interior’s theme. Face it with a piece of set-aside glass. Cut a piece of mat-board or something similar and cover it with your interior finish…wallpaper, paneling, etc. Between the out-facing piece and the interior one fill in with mat-board or whatever, so the finished walls will be flush with the frame corners. Glue the assembled wall/s in place. Add thin decorative molding to edges if appropriate to your theme.
Back view of THE GOOD EGG
Back view of a MATTERS OF THE HEART, a valentine store, using a vintage valentine card.
-Insert a piece of frame glass into the other openings and hold with a bit of tacky glue or tiny glue dots. You may choose to wait until you have designed the interior before permanently adding the glass wall/s and then adding the furnishings, etc. from the top opening.
-Using ¼” square stripwood to make a ledge around the interior top of the box, to support a protective piece of glass that can be removed for easy access. The corners of these pieces can be mitered or butted to each other. Paint to match the frame. Glue them in place so they will sit down 1/8” down from the top of the box. Cut or have cut the one of the extra pieces of frame glass a scant smaller than the top opening. Sand edges smooth.
-Turn the box over and measure and cut a bottom cover piece of art paper scant smaller than the box bottom. This can be in a color to match the frame or painted to match. Glue stick in place to bottom. A decorative peg, button, wood turning, piece from a small wooden chess set, etc., may be glued or nailed to each corner for a finished look or to lift the box high enough to add a thin transformer/battery to the underside, if lighting is to be added to your setting.
This is Happy Trails, a 2004 child's cowboy themed bedroom.
It uses four 8" x 10" frames making it approx. 10" high and 8" square
It has two solid walls and two glass walls.
You can also see the wooden feet on the bottom corners
This setting from 2004, celebrating women's right to vote, has two adjoining solid walls and 2 glass walls.
These two photos of a boy's nautical themed bedroom show how much can be shown in a little space without seeming cramped because of the two glassed in sides.
FRAME BASE LAMP
The lamp and base are easy to assemble and the supplies nead not be pricey. Construct the framed room as instructed above, using six 5" x 7" picture frames., four for the sides and one each for the top and bottom. The top and bottom frames are glued, centered over the top and bottom of the frame structure, flat edges to flat edges.
You should be able to find the wiring supplies at a lighting specialty shop or online. Measure & cut a beam from a length of 3/4" x 1/2" wood, fitting the beam snugly from the front to the back of the box on the frame just above the back wall (see figure below). Paint or stain the beam to match the frames. Drill a hole through on 3/4" side of the beam, centered side to side, that is slightly smaller in diameter, than the brass post. Screw one of the threaded decorative brass pieces on the bottom of the post and then screw the post into the hole. Use the nut to secure it from the bottom. The nut may be recess into the bottom of the beam by drilling a larger hole from the bottom. Tighten the decorative thread-cover down onto the top of the beam. Cover the nut with tape painted to match beam.
Assemble the socket and wire per manufacturer's instructions, following all safety precautions (see figure below).
Insert the 2nd decorative thread-cover onto the top of the post threads, insert theharp, and screw on the socket. As you screw it on, make sure the wire extends the back inline with the wood beam.
When the assembly is done, use a combination of Tack glue and cyanoacrylate glue (Super/Crazy etc.) to adhere the beam ends to the inside of the frame box, centered side to side, and in line with the inside of the of the front and back frame. Let glue set before attaching the shade. The shade is secured to the harp with a finial. A 40-watt bulb is recommended.
-4" brass lamp tube/post, threaded at both ends with brass nut to fit post
-3/4" x 1/2" wood, approx. 5-1/2" long
-Two threaded decorative brass pieces to cover threads of lamp post
-Brass socket with hole to take wire (Note: Most sockets sold have the wire coming down through the bottom of the socket and into the post. You will need the type sold for bottle and jar lamps with the wire coming out of the side. If you can not find this type sold separately, purchase a kit for bottle lamps).
-8" to 10" harp
-Lamp shade approx. 9-1/2" high, with approx. 13" diam bottom.
-Electrical cord with attached plug
-Off & on switch for cord (optional)
Note: A quick online search came up with this site http://www.lampshop.com that should have the wiring supplies you will need for the lamp. Interesting...the clamp-on-style, which I had not seen before, could work out nicely and not be as fiddly to install....I will have to investigate!
I hope I have answered the questions concerning the use of picture frames to construct room boxes for those that asked and have inspired you and others to try this method. I think you will find it fast and rewarding with many options for displaying your miniatures.
So many of you have wondered why I did not add more projects to fill the AMERICANA CART and expressed your concern...well, all I can say is that it was a long, hot summer here that seemed to extend into fall. And living on the beach nice weather means lots of
company. Not complaining, as it also meant lots of hugs and kisses from grandchildren, many a bonfire and oodles of s'mores & ghost stories, delicious pots of clams and crabs and good times had by all. But it did not leave me time and energy to even think about miniatures...and truthfully, that isn't always a bad thing.
So, with a crispness to the air, leaves beginning to fall, pumpkin patches full, I think I feel a bit renewed and ready to jump back in to this blog. I am working on a Halloween project and if all goes right you will "see me" soon.
Happy Fall to all of you who follow this blog,.. I am amazed at the traffic here and the amount of new followers even without my presence. A special hello to all of you who have visited from Russia in the past month.